Basic sourcesStandard textbooks of surveying; Indian Standards (levelling, surveying instruments); Indian Railways Permanent Way Manual (IRPWM 2020) — chapters on curves and gradients; Engineering Code (surveys). Railway curves in detail — PW.3.
1Surveying — Basic Principles and Instruments
In simple wordsThe two basic principles of surveying — working from the whole to the part, and fixing every new point from at least two known points; along with the instruments.
- Two basic principles: "from the whole to the part" (first the main control points, then the details, so that errors do not accumulate) and fixing a new point from at least two known points.
- Linear measurement: chain/tape — corrections for temperature, pull, sag and slope; Electronic Distance Measurement (EDM).
- Angular measurement: compass (bearings — whole circle WCB and quadrantal QB), theodolite (horizontal and vertical angles), total station (angle + distance + coordinates, data collection).
- Modern: GPS/DGPS, photogrammetry by drone (UAV), LiDAR — fast and accurate in surveys for new lines; satellite imagery and GIS (PM Gati Shakti portal).
2Levelling
In simple wordsLevelling = finding the height (RL) of points on the ground — from back sights and fore sights.
FormulaHeight of instrument (HI) = RL of the known point + back sight (BS); RL of a point = HI − fore/intermediate sight (FS/IS)
FormulaCheck: ΣBS − ΣFS = last RL − first RL (= Σ rise − Σ fall)
ExampleBench mark RL 100.000 m; BS on it = 1.450. FS on the next point A = 0.820.
HI = 100.000 + 1.450 = 101.450; RL(A) = 101.450 − 0.820 = 100.630 m (rise 0.630).
- Errors: collimation error, curvature of the earth and refraction — keeping the back-sight and fore-sight distances nearly equal largely cancels the effects of collimation and curvature; combined curvature-and-refraction correction ≈ 0.0673 d² m (d in km).
- Contours: points of equal height; closely spaced lines = steep slope; they do not cross each other (except at an overhang). Used in choosing a rail alignment and working out the quantity of earthwork.
3Horizontal Curves — Geometry and Setting Out
In simple wordsA horizontal curve joining two straight tracks — its geometry and laying it out on the ground.
FormulaTangent length T = R tan(Δ/2); length of curve L = π R Δ / 180; external distance E = R [sec(Δ/2) − 1]
FormulaDegree of curve (on a 30.5 m chord): D ≈ 1750 ÷ R (R in metres) — the radius of a 1° curve is about 1750 m
FormulaVersine on a 20 m chord (mm) ≈ 50,000 ÷ R (m) — general formula V = C² ÷ 8R
- Rankine's method of deflection angles: with a theodolite — the deflection angle for each chord δ (minutes) = 1718.9 × c ÷ R; accurate, for long curves.
- Two-theodolite and offset (from chords/tangents) methods — for short curves and lower accuracy.
- Transition curve: the radius reduces gradually from the straight to the circular curve and the cant increases gradually — a cubic parabola in the Railways; determining its length in PW.3.
- Vertical curves: at changes of gradient — summit and valley curves; required when the change of gradient exceeds a limit.
ExampleR = 875 m, Δ = 30°.
T = 875 × tan 15° = 875 × 0.2679 ≈ 234.4 m; L = π × 875 × 30 ÷ 180 ≈ 458.1 m; degree ≈ 1750 ÷ 875 = 2°; versine on a 20 m chord ≈ 50,000 ÷ 875 ≈ 57 mm.
RememberQuick revision —
- Principles: from the whole to the part; fixing from two known points.
- HI = RL + BS; RL = HI − FS; ΣBS − ΣFS = last − first RL.
- Curvature-and-refraction ≈ 0.0673 d²; keep the BS and FS distances equal.
- T = R tan(Δ/2); L = πRΔ/180; D ≈ 1750/R; versine on a 20 m chord ≈ 50,000/R mm.
- Rankine: δ = 1718.9 c/R minutes.
Exam trap
- HI = RL + BS; RL = HI − FS — don't reverse the signs.
- To reduce the curvature-and-refraction error, keep the BS and FS distances equal.
- Degree of curve D ≈ 1750/R; versine on a 20 m chord ≈ 50,000/R mm.